Switchboxes
Single boom or dual boom switchboxes incorporate Off, Auto (On), and Ground Speed Override (GSO) functions into a single unit. Boom sense cables are available for vehicles with built in switches.
|
Part |
Description |
Note |
|
405-0075 |
Single Conveyor Switchbox with Off/Auot/GSO |
w |
|
405-0098 |
Dual Boom Switchbox with Off/Auto/GSO - to twin Mid-Tech Connectors |
w, x |
|
404-0062 |
Switchbox with Off/Auto/GSO |
y |
|
404-0050 |
Off/Auto/GSO Panel Mount Switch |
y |
|
105-0024 |
Air-Max Switchbox, Dry only (LH/RH Boom off) |
z, w |
|
105-0025 |
Air-Max Switchbox with Wet Boom (LH/RH Boom off) |
z, w |
|
405-0036 |
Boom Status Cable |
Note:
w - Incorporates Boom Status Cable.
x - Use 402-0040 or 402-0065 to adapt DICKEY-john 360 Slot Sensor
to this box.
y - Use in conjunction with Boom Status Cable.
z - Requires special cables. Refer to the Air-Max System.
Application Rate Sensors
Rate sensors are used to measure the speed of the conveyor. Slotted disk sensors can be mounted on a conveyor drive, idler or jackshaft. Inductance type sensors can read from a sprocket or a gear mounted on the conveyor drive or jackshaft.
|
Part |
Description |
Note |
|
16-05000 |
Gear Sensor |
ff, dd |
|
16-05004 |
Gear Sensor with 20' (6.0 m) Cable |
aa, dd |
|
120-0009 |
360 Slot Application Rate Sensor with 10' (3.0 m) Cable |
cc |
|
120-0042 |
Inductance Rate Sensor with 9' (2.7 m) Cable |
aa, dd |
|
67-00004 |
1" Round Shaft Coupler for 120-0009 | |
|
Co-Application Components |
||
|
105-0007 |
Chemical Flow Monitor, Alarm Console - 4 Position | |
|
405-0066 |
Hopper Level Interface Cable | |
|
600-0056 |
12 VDC Motor Assembly with Sensor | |
|
120-0008 |
30 Slot Application Rate Sensor - 12' (3.7 m) Cable |
ee |
|
120-0008-P |
60 Slot Application Rate Sensor - 12' (3.7 m) Cable |
ee |
|
120-0040 |
Proximity Sensor with 6' (1.8 m) Cable, Amp Connector |
mm |
|
120-0043 |
Proximity Sensor with 9' (2.7 m) Cable, Amp Connector |
mm |
|
105-0104 |
40 Amp Granular Bin Driver Module | |
|
105-0105 |
10 Amp Granular Bin Driver Module | |
|
602-0014 |
12' Signal Extension Cable | |
|
Hydraulic Motors |
||
|
28-05004 |
Hydraulic Motor with Sensor 300 rpm @ 10 gpm, 7.7 in3/rev. (38 l/min, 126 cm3/rev.) (Painted Black with Mounting Hardware) |
1 |
|
600-0060-P |
Hydraulic Motor with Sensor 500 rpm @ 10 gpm, 4.6 in3/rev. (38 l/min, 75.4 cm3/rev.) |
1 |
|
600-0061-P |
Hydraulic Motor with Sensor 144 rpm @ 10 gpm, 15.9 in3/rev. (38 l/min, 261 cm3/rev.) |
1 |
|
Options |
||
|
28-10001 |
Seal Kit for 28-02005 Hydraulic Motor | |
|
600-0090 |
Sensor for above Hydraulic Motors | |
Note:
|
aa - |
Requires a metal object (i.e. Sprocket Teeth) from which to read pulses. Contact TeeJet. |
|
cc - |
Does not require an Adapter Cable when used with 404-0061 or 404-0047. |
|
dd - |
Use with 405-0098 or with Standard Flow Control Cable 404-0022, or with 405-0074 and 405-0174 Power and Flow Control Harnesses. |
|
ff - |
Requires 45-06114 or 45-05141 Cable. |
|
ee - |
Use with 105-0104 Driver Module only. |
|
mm - |
Use with 105-0105 Driver Module only. |
|
1 - |
Manifold mount for EXR IV Hydraulic Control Valves. |
TeeJet Granular Components